Question 1

Can polycarbonate light transmittance be degraded over time?

Accepted Answer

SUNTUF roofing sheets are made with a UV protection layer. This layer protects the sheets from UV radiation harm and maintains light transmittance and quality for many years.

Question 2

PALRUF PVC or SUNTUF polycarbonate corrugated sheets: when to use which?

Accepted Answer

PVC corrugated sheets are typically used in highly-corrosive environments such as port warehouses, cowsheds, and dairies for opaque roofing and siding. When natural daylight illumination is needed, polycarbonate corrugated sheets are used as roofing or siding.

Question 3

Is PALRUF resistant to UV radiation?

Accepted Answer

Yes, PALRU corrugated PVC roofing sheets are UV resistant.

Question 4

Can I step on SUNTUF skylights during or after installation?

Accepted Answer

Although SUNTUF is remarkably strong and can support extreme loads, for your safety, do not stand directly on the sheets. If it can’t be avoided, use stepping ladders, platforms or crawling boards.

Question 5

How to clean polycarbonate roofing?

Accepted Answer

Here are some steps to clean your polycarbonate roofing sheets:

Remove any loose debris, such as leaves or twigs, from the sheets surface using a broom or leaf blower.

Dip a soft cloth or sponge into a bucket of warm water and gently scrub the sheets, working in small sections at a time.

Rinse the sheets thoroughly with water to remove any remaining dirt or soap suds.

Dry the sheets with a clean and soft cloth, or allow them to air dry.

Avoid using high-pressure water or a pressure washer. High pressure can damage the sheets' surface.

Avoid using harsh chemicals or abrasive cleaners, as they can damage the sheets' surface. Before using a detergent, ensure it is polycarbonate-compliant.

If the sheets are particularly dirty or have stains that are difficult to remove, you may need to repeat the cleaning process a few times to get them fully clean.

In addition to cleaning the sheets, it is also worthwhile to regularly inspect the roofing for damage or wear.

Question 6

How do I combine SUNTUF rooflights or sidelights with corrugated metal roofing?

Accepted Answer

Palram's MetalMatch technology enables a precise match of corrugated SUNTUF to almost any industrial metal sheet. Contact your local Palram office for more details.

Question 7

Can I use PALRUF clear PVC corrugated sheets for industrial skylights?

Accepted Answer

PALRUF is an excellent skylight panel. It can overlap corrugated metal sheets and other types of corrugated roofing panels. PALRUF skylights are resistant to chemicals and fumes, and are an ideal solution for the chemical industry.

Question 8

Can I install PALRUF corrugated PVC and SUNTUF corrugated polycarbonate sheets horizontally for siding?

Accepted Answer

Yes. Make sure you start installing from the bottom up so overlaps prevent water from penetrating indoors.

Question 9

What kind of gasket is suitable for corrugated SUNTUF and PALRUF sheets?

Accepted Answer

Flexible EPDM gaskets with metal washers.

Flexible EPDM gaskets allow just enough free movement for the sheets as they contract and expand. This ensures an effective seal against leaks and reduces stress and micro cracks. The metal washers will distribute the fastener load and will support the gasket.

Gaskets should conceal holes properly.

Use a 25mm gasket for a 10mm drill. A 19mm gasket is the alternative when the corrugation profile does not allow a wider gasket (if the valley or crest is too narrow).

Question 10

Which screws to use for fixing corrugated SUNTUF and PALRUF roofing sheets?

Accepted Answer

Use corrosion-resistant screws for optimal long-term service

Use screws with an outside thread diameter of ¼”

Screw shaft length varies with corrugation profile and fixing location (crest or valley).

Use self-tapping screws for timber purlins, and self-drilling screws for metal purlins.

Question 11

Why do polycarbonate roofing sheets require pre-drilling oversized holes?

Accepted Answer

Polycarbonate sheets are typically attached to support structures using screws or other fasteners. It is necessary to pre-drill oversized holes in the SUNTUF sheets to allow for expansion and contraction due to temperature changes. This is critical to ensuring the roof's quality and performance over time.

Question 12

How to accommodate SUNTUF polycarbonate roofing sheets' thermal expansion?

Accepted Answer

Polycarbonate roofing sheets can accommodate thermal movement by following these guidelines:

Keep a small gap where the SUNTUF sheets meet another object. Sheets expand most along their length, so pay attention to this direction.

Pre-drill oversize holes around the fixings. In this way, the screws won't stress the sheets.

Polycarbonate ridge caps, wall connectors, and flashings should also be predrilled with oversized holes.

Applying foam tape along structural elements that come in contact with sheets will reduce friction noise.

Leave a 5cm-10cm overhang over the lower purlin.

Question 13

How to Cut SUNLITE Multiwall Polycarbonate Roofing Panels?

Accepted Answer

Multiwall polycarbonate sheets are strong, durable, lightweight, and provide excellent thermal insulation. These features make them ideal for professionals and DIY enthusiasts alike. On-site tailoring and trimming is simple. Follow these guidelines to ensure quality results.

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Place a layer of cardboard or plywood on the workbench before placing the first sheet. This will protect the surface from scratches.

Place one multi-wall panel on your workbench. You should cut one sheet at a time, and not stack sheets together.

Multiwall polycarbonate sheets come with protective films. This film indicates which side of the panel is UV-protected. Do not remove it. You will need it later.

Use a measuring tape to measure the sheet, and make pen marks at each end. Join the marks with a ruler.

Do not rush measuring and marking. Once trimmed, you cannot patch the sheets together.

Secure the polycarbonate sheet to the workbench surface to prevent movement and vibrations.

Support the sheet near the cutting line. You can do this by placing a timber plank on top of it, parallel to the markings.

Cut along the marked pen line. The preferred method is to use a fine-tooth saw that rotates at high speed.

Advance the saw slowly and steadily and do not stop once you have begun. It will ensure a clean, consistent edge.

Clean the sheet’s channels with compressed air.

Remove leftover cuts and scraps from the cutting table.

Question 14

What Is the Correct Saw for Cutting SUNLITE Polycarbonate Multiwall Sheets?

Accepted Answer

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

You can cut twin-wall or multi-wall polycarbonate sheets using standard workshop equipment. This includes a common circular saw, a jigsaw, a hacksaw, and a hand saw.

Power tools

Circular table saws are the most efficient and accurate way to cut plastic sheets. This option, however, is rarely available on home improvement sites.

A portable fine-toothed circular saw is ideal for cutting on-site. High blade speed and moderate feeding rate will give you the best results.

A jigsaw also produces clean, accurate cuts, but requires better control. It is most suitable for cutting complex shapes and curved lines.

Manual tools

Working with manual tools is time-consuming, but it reduces the risk of sheet damage.

Manual handsaws or hacksaws with fine teeth provide accuracy and control.

Hand tools such as tin snips, scissors, or even a utility knife are useful for making small notches.

Additional tools

You will need a flat, stable workbench to work on.

To set guidelines, you will need a tape measure, a ruler, and a marking pen.

An air-compressor will help you remove chips that may have entered the sheets’ cells.

Question 15

How to Cut PALRUF Corrugated PVC Roofing Sheets DIY?

Accepted Answer

Corrugated PVC sheets are popular for garden shed roofing and outdoor canopies. A durable solution that provides strength and resistance to moisture and chemicals. On-site tailoring and trimming is simple. Follow these guidelines to ensure professional results.

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Place a layer of cardboard or plywood on the workbench before placing the sheets. This will protect the surface from scratches.

Place the PVC panels on your workbench.

Clamp a few sheets together. This will reduce vibrations.

Use a measuring tape to measure the sheet, and make pen marks at each end. Join the marks with a ruler.

Do not rush measuring and marking. Once trimmed, you cannot patch the sheets together.

Secure the PVC sheets to the workbench surface to prevent movement and vibrations.

Support the sheets near the cutting line. You can do this by placing a timber plank on top of the sheets, parallel to the markings.

Cut along the marked pen line. The preferred method is to use a fine-tooth saw that rotates at high speed.

Advance the saw slowly and steadily and do not stop once you have begun. It will ensure a clean, consistent edge.

Remove leftover cuts and scraps from the cutting table.

Question 16

What Is the Right Saw for Cutting PALRUF Corrugated PVC Sheets?

Accepted Answer

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Power tools

Circular table saws are the most efficient and accurate way to cut plastic sheets. This option, however, is rarely available on home improvement sites.

A portable fine-toothed circular saw is ideal for cutting on-site. High blade speed and moderate feeding rate will give you the best results.

A jigsaw also produces clean, accurate cuts, but requires better control. It is most suitable for cutting complex shapes and curved lines

Manual tools

Working with manual tools is time-consuming, but it reduces the possibility of sheet damage.

Manual handsaws with fine teeth provide accuracy and control

Hand tools such as tin snips, scissors, or even a utility knife are useful when working with thin PVC sheets or making small notches.

Additional tools

You will need a flat, stable workbench to work on.

To set guidelines, you will need a tape measure, a ruler, and a marking pen.

Question 17

How to Store PVC Sheets?

Accepted Answer

PVC sheets are durable and chemically resistant and guaranteed to last for many years if handled properly.

Here are some tips for storing PVC sheets to ensure you get the most out of your investment.

Store your PVC sheets horizontally on a flat surface, such as a pallet or a shelf.

Ensure that no nails or bolts protrude from the platform. Even small rocks can leave permanent dents and scratches on the sheets.

Stack the largest sheets at the bottom, and the shorter, smaller panels on top.

Avoid stepping on PVC panels and placing heavy or sharp equipment on them.

Ensure that the PVC sheets are stored in a dry, ventilated, cool, shaded area away from direct sunlight.

Do not stack transparent or translucent sheets over opaque PVC sheets.

Avoid covering the sheets with dark films or other heat-absorbing materials.

Cover the panels with an opaque, bright, waterproof cover if you intend to leave them outdoors.

Keep your stack dry to prevent whitening and water spots.

Question 18

How many side overlaps does SUNTUF or PALRUF corrugates roofing require?

Accepted Answer

With a proper roof pitch, an overlap of one corrugation between sheets will keep the roof leak-safe, as long as the sheets are laid correctly.

Find the primary direction wind and rain are expected to come from and place the first sheet in the opposite direction. The next sheet will overlap the first, and so on. By doing so, you reduce the chance that water and dust will penetrate between the sheets.

Question 19

Which side of the SUNTUF roofing sheet should face up?

Accepted Answer

Look for a removable strip that indicates which side of the sheet is UV-protected.

It is critical to install the sheets with the UV-protected side facing up.

Remove the marking strip after installation.

Question 20

What is the recommended purlin spacing for SUNTUF corrugated polycarbonate roofs?

Accepted Answer

The required purlin spacing for corrugated polycarbonate roofing depends on a number of factors, including the size and type of corrugated sheets. In addition, the type of support structure, and local building codes.

Follow Palram's technical guidelines for the specific SUNTUF product you have chosen. This will ensure that the roofing is properly supported and able to withstand the loads and stresses it will be subjected to.

Question 21

Can SUNTUF corrugated polycarbonate or PALRUF PVC sheets be bent into arches?

Accepted Answer

Corrugated plastic sheets are tough and flexible. You can easily bend them to a curved roof without losing material integrity. There is only one rule: stay within the allowed arch radius.

In simple terms, an arc is a segment of a circle, and its radius is equal to its circle's radius.

Your sheet's minimum bending radius is determined by its profile (corrugation) and thickness.

Typical DIY polycarbonate corrugated sheets can bend to an arc radius of 4,000mm. Some of the more robust sheets require a minimum radius of 7,000mm. Check the specs of your sheeting to be sure.

Question 22

What is the right roof pitch for SUNTUF and PALRUF corrugated plastic sheeting?

Accepted Answer

A proper slope keeps water off the roof. It prevents leaks, keeps the roof clean, and ensures structural integrity.

Roof slope percentage indicates how much the roof falls over a given distance. For example, the roof slope would be 5% if it dropped 5 centimeters over one meter.

DIY corrugated plastic sheet typically requires a 10% slope. Some profiles call for a deeper slope. Check the specs of your sheeting to be sure.

Pay attention: If you expect leaves or snow to accumulate on your roof, consider a deeper slope.

Question 23

How to Install SUNTUF Corrugated Polycarbonate Roofing Sheets DIY?

Accepted Answer

Specifications vary between different products and sheet profiles. Read the installation instructions for the specific roofing sheet you have chosen and follow them carefully.

Here is a general outline of the steps involved in installing corrugated polycarbonate roofing panels:

Have your roofing framework built, including rafters and purlins with appropriate spacing.

Measure and mark the area where the panels will be installed.

Trim the sheets to the right length, if needed.

Place the first panel on the roof and align it with the roof edge.

Before securing the panel to the roof frame, remember:

Place the fixings in the right places.

Use suitable screws and gaskets.

Pre-drill oversized holes to allow thermal movement.

Repeat the process with the remaining panels, overlapping and align them with the corrugations.

If needed, add additional flashing.

It is important to follow the manufacturer's installation instructions carefully and use the appropriate fasteners and sealants to ensure a secure and durable installation.

If you are unsure about how to install the panels or are not comfortable with the process, it is recommended to hire a professional contractor to do the job.

Question 24

How to Cut SUNTUF Corrugated Polycarbonate Roofing Sheets DIY

Accepted Answer

Corrugated polycarbonate sheets are common roofing materials for DIY garden shelters and outdoor canopies. On-site tailoring and trimming is simple. Follow these guidelines to ensure quality results.

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Place a layer of cardboard or plywood on the workbench before placing the sheets. This will protect the surface from scratches.

Place the polycarbonate panels on your workbench.

Clamp a few sheets together. This will reduce vibrations.

Polycarbonate sheets come with a removable protective film or marking strip. This film indicates which side of the panel is UV-protected. Do not remove it. You will need it later.

Use a measuring tape to measure the sheet, and make pen marks at each end. Join the marks with a ruler.

Do not rush measuring and marking. Once trimmed, you cannot patch the sheets together.

Secure the polycarbonate sheets to the workbench surface to prevent movement and vibrations.

Support the sheets near the cutting line. You can do this by placing a timber plank on top of the sheets, parallel to the markings.

Cut along the marked pen line. The preferred method is to use a fine-tooth saw that rotates at high speed.

Advance the saw slowly and steadily and do not stop once you have begun. It will ensure a clean, consistent edge.

Remove leftover cuts and scraps from the cutting table.

Question 25

What Is the Right Saw for Cutting SUNTUF Corrugated Polycarbonate Sheets?

Accepted Answer

Safety First: Protect yourself by using professional equipment, keeping your surroundings neat and tidy, and using tools with caution and care.

Power tools

Circular table saws are the most efficient and accurate way to cut plastic sheets. This option, however, is rarely available on home improvement sites.

A portable fine-toothed circular saw is ideal for cutting on-site. High blade speed and moderate feeding rate will give you the best results.

A jigsaw also produces clean, accurate cuts, but requires better control. It is most suitable for cutting complex shapes and curved lines

Manual tools

Working with manual tools is time-consuming, but it reduces the possibility of sheet damage.

Manual handsaws with fine teeth provide accuracy and control.

Hand tools such as tin snips, scissors, or even a utility knife are useful when working with thin polycarbonate sheets or for making small notches.

Additional tools

You will need a flat, stable workbench to work on.

To set guidelines, you will need a tape measure, a ruler, and a marking pen.

Question 26

What size do bullet resistant polycarbonate sheets come in?

Accepted Answer

PALSHIELD ballistic grade polycarbonate is available in a variety of sizes and specifications. Custom size options are available upon request.

Question 27

How to Store Polycarbonate Sheets?

Accepted Answer

Polycarbonate sheets are tough and durable and guaranteed to last for years.

Here are some tips for storing polycarbonate sheets to ensure you get the most out of your investment.

Polycarbonate should be stored horizontally on a flat surface, such as a pallet or a shelf.

Ensure that no nails or bolts protrude from the platform. Even small rocks can leave permanent dents and scratches on the sheets.

Stack the largest sheets at the bottom, and the shorter, smaller panels on top.

Avoid stepping on polycarbonate panels and placing heavy or sharp equipment on them.

Store the polycarbonate sheet in a dry, cool, ventilated, shaded area away from direct sunlight.

Keep your stack dry to prevent whitening and water spots.

Avoid covering the sheets with dark films or other heat-absorbing materials.

Cover the panels with an opaque, bright, waterproof cover if you intend to leave them outdoors.

Question 28

What are three-dimensional or 3D logo signs?

Accepted Answer

3D letters and/or 3D logos are made of plastic, metal or foam. They reinforce an upscale image and create a clear highlighted message. These signs can be illuminated when required.

Question 29

How do I curve the polycarbonate to follow the façade curve?

Accepted Answer

All Palram polycarbonate products can be cold bent onsite during installation, subject to a minimum radius. The radius varies based on the chosen product. For flat sheets such as PALSUN & SUNLITE, the rule-of-thumb for the minimum radius is the thickness multiplied by 200. Please check the Palram catalog for more detailed specifications.

Question 30

How do I specify the required thickness of the polycarbonate glazing material?

Accepted Answer

The recommended thickness of the polycarbonate glazing material is based on factors such as wind & snow load, panel size, and boundary conditions. Visit the Palram website for access to calculators that can help you determine the recommended thickness.

Question 31

How do I reduce the heat build-up coming from the façade into the building?

Accepted Answer

In order to reduce heat build-up through the façade, Palram strongly recommends the use of its tinted SolarSmart™ panels. SolarSmart™ tints can be implemented in all Palram polycarbonate products. For more information, reference the Palram SolarSmart™ technology page.

Question 32

How do I create a double skin glazing solution for façades and curtain walls?

Accepted Answer

Flat solid or multiwall sheets can be glazed in double skin applications using standard aluminum curtain wall profiles and EPDM gaskets. The SUNPAL system can be installed in a double skin application with a special aluminum profile provided by Palram.

Question 33

Can flat solid polycarbonate be installed in a similar manner to glass in curtain wall applications?

Accepted Answer

PALSUN can be installed with standard curtain wall aluminum glazing profiles and EPDM gaskets (similar to glass), or spider fixing spaced with approximately 400 mm centers. However, it cannot be used with structural silicone and PALGARD (PALSUN) with anti-scratch coating is the recommended substitute in this case.

Question 34

Should products be pre-dried before thermoforming?

Accepted Answer

This depends on the production date and storage conditions of the product before thermoforming. It is recommended to check the product before thermoforming is attempted.

Question 35

Is the PE film suitable for thermoforming applications?

Accepted Answer

Most of Palram's products that are delivered with PE film covering are suitable for thermoforming. In general, we recommend using clear PE and not printed PE.

Question 36

How do I polish the edges of acrylic?

Accepted Answer

Acrylic edges can be polished by heating them with a torch, blowing hot air on them, or rotating a brush with wax.

Question 37

What is the minimum allowed bending radius of polycarbonate?

Accepted Answer

The minimum allowed bending radius of the polycarbonate is 200 times the thickness of the sheet, for example, a 2 mm sheet has a minimum 400 mm bending radius.

Question 38

What are the dimensions of PALCLAD Pro sheets (size and thickness)?

Accepted Answer

PALCLAD Pro comes in a standard size of 1500x3000 mm and in thicknesses of 2 and 2.5 mm.

Question 39

What is the range of colors for PALCLAD Pro?

Accepted Answer

PALCLAD Pro comes standard in white and off-white. In addition, 10 more colors are available on special order. PALCLAD Pro can be printed on with excellent ink adhesion to surface and print quality.

Question 40

What is the difference between antimicrobial and antibacterial?

Accepted Answer

Antimicrobial and antibacterial are interchangeable in many cases. However, antimicrobial offers further protection by eliminating fungi, that is, by eliminating any mold or potential mold build-up.

Question 41

Can I use multiwall polycarbonate sheets as a skylight combined with a metal roof?

Accepted Answer

Yes, you can by using domes or glazing solutions. Please contact Palram technical support for further information.

Question 42

How do I install flat solid or multiwall polycarbonate sheets as skylights?

Accepted Answer

Flat solid or multiwall polycarbonate sheets need to be installed with designated aluminum profiles when used as a skylight.

Question 43

How do I install corrugated polycarbonate sheets as a skylight?

Accepted Answer

Corrugated polycarbonate sheets are installed as a homogeneous part of the metal roof. For more information, please review Palram's installation instructions for the desired profile.

Question 44

Can I use clear PVC corrugated sheets for skylights?

Accepted Answer

Clear corrugated PVC sheets can function as skylights incorporated into metal or other types of roofing. Note that this is only suitable for areas with cold climates.

Question 45

Why do I have to pre-drill fastener holes in roofing with corrugated panels?

Accepted Answer

Pre-drilling the holes ensures that the panels have room to expand and contract properly with temperature changes. Skipping this step can lead to distorted, warped or cracked panels.

Question 46

Can the percentage of light transmission be controlled? I need a lot of light but I need it to be diffused.

Accepted Answer

Palram offers various LT% parameters - from 0% to 90%. In addition, we offer a color called a “diffuser” that allows 85% of the light in while diffusing it by 100%. The result is a light-transmitting panel that is not transparent but is highly translucent.

Question 47

If polycarbonate sheets block UV radiation, why is there a "UV-side" that faces outwards?

Accepted Answer

Polycarbonate sheets block UV radiation by absorbing it. This absorption mechanism can cause degradation to the material, and to prevent this from happening, the sheet is coated with a special material. For this reason, it is recommended that the sheets are installed with the marked UV protective layer facing outward. Moreover, most of the sheets are only protected on the side that is clearly marked as such.

Question 48

Is PALRUF resistant to UV radiation?

Accepted Answer

Yes, PALRUF corrugated PVC is resistant to UV.

Question 49

Is it OK to walk over PALRUF roofing sheets, during or after installation?

Accepted Answer

No. If it can’t be avoided during installation, use stepping ladders, platforms or crawling boards to prevent walking directly over PALRUF roofing sheets.

Question 50

My building inspector says I need the fire certification for PALRUF. Can you provide this information?

Accepted Answer

Yes. We can provide test reports and other such documents. Please contact your Palram dealer if you require this data.

Question 51

When roofing with PALRUF corrugated panels, where should I fix the screws – valley or crest points?

Accepted Answer

Crest fixing is preferred.

Question 52

When roofing with PALRUF corrugated panels, where should I start to install?

Accepted Answer

You can choose to install left to right, or right to left. It is recommended to always advance against the dominant wind direction at the site. Never start at both sides, or at any two separate points.

Question 53

How do I design the secondary steel support spacings for roofing/siding?

Accepted Answer

Palram created specific loading tables for each product. Please visit our website and download the specific catalog.

Question 54

Can I install multiwall polycarbonate sheets horizontally for siding?

Accepted Answer

No. The multiwall channels should always be vertical to allow condensation water to drain out by gravity.

Question 55

Can I install corrugated PVC and polycarbonate sheets horizontally for siding?

Accepted Answer

Yes. Make sure you start installing from the bottom up so the overlaps will not let the water in.

Question 56

Are there customized sizes of BULLETPROOF sheets?

Accepted Answer

Yes, BULLETPROOF is available in custom sheets of up to four square meters.

Question 57

What is the protection level for ballistic?

Accepted Answer

For bullets, BULLETPROOF offers UL 752 protection up to level 6 — protection against automatic weapons firing pistol-caliber ammunition such as an Uzi sub-machine gun chambered in 9 mm.

Question 58

What level of protection against forced entry can I expect from BULLETPROOF?

Accepted Answer

BULLETPROOF offers forced entry protection equivalent to ASTM F1915-05 Security Grade Level 1-3 — a standard developed to measure impact-resistant fittings in correctional facilities.

Question 59

How do I clean the polycarbonate?

Accepted Answer

Never use abrasive or high alkaline cleaners on any Palram polycarbonate products.
Do not leave cleaners on Palram polycarbonate for extended periods of time. Rinse immediately with cold, clean water.
Do not apply cleaners in direct sunlight.
Never use sharp objects, squeegees or razors on polycarbonate.
Do not clean with gasoline.
Always practice safety first and never step directly on a polycarbonate panel.
Always test cleaners in a small inconspicuous area prior to cleaning the entire panel to ensure against adverse results.
Avoid allowing the pressure washer spray tip to come too close to the panel. Pressure washers often have enough pressure at the spray tip to penetrate or tear the panel.
Avoid dry cleaning as sand and dust particles clinging to the exterior of the panels may scratch the surface.

Question 60

How do I combine corrugated polycarbonate sheets (SUNTUF) with metal sheets?

Accepted Answer

With Palram's MetalMatch technology, we can perfectly match almost any trapezoid industrial metal sheet and install SUNTUF as a homogeneous part of the roof.

Question 61

What are the common applications of corrugated PVC sheets?

Accepted Answer

The common applications of corrugated PVC sheets are buildings that require opaque coverings and/or are located in highly-corrosive environments such as chemical plants, coastlines, cowsheds, and dairies.

Question 62

When should I use PVC corrugated sheets versus polycarbonate corrugated sheets?

Accepted Answer

PVC corrugated sheets are mainly used for opaque roofing and siding of industrial buildings in highly-corrosive environments such as port warehouses, cowsheds, and dairies. Polycarbonate corrugated sheets are mainly used as roofing or siding where natural daylight illumination is needed.

Question 63

What are the benefits of using polycarbonate standing-seam system over standard polycarbonate sheets?

Accepted Answer

The main benefit of the standing-seam system is that unlike standard sheets, it is sold together with all installation accessories. This system also provides superior water tightness and is easier and faster to install.

Question 64

What is the meaning of Shading Coefficient (SC)?

Accepted Answer

Shading coefficient (SC) is a parameter that compares transparent and translucent materials with clear 3 mm glass with 87% LT ׂ(light transmission). The lower the value, the more convenient it is to stay under the material on warm, sunny days. In architectural projects, the SC should usually be between 0.3 to 0.5.

Commercial

Residential

Commercial

Residential

FREQUENTLY ASKED QUESTIONS

Question subject + -

Market Segment + -

Product + -

Contact Us

Question subject + -

Market Segment + -

Product + -

Contact Us

Palram.com uses cookies